Atwood Levelegs System Adapter Kit Manual de usuario descargar pdf

LITERATURE NUMBER

MPD 61050

LEVELEGS

™

SYSTEM

ADAPTER KIT

ENGLISH,

FRANÇAIS (et Canada) Effective 12/12/07

24 HOUR TROUBLESHOOTING HELP CALL - 800-884-7012

Provided by Coach Net

, the largest RV owner support company in North America.

•Installation •Operation •Maintenance

SAFETY ALERT SYMBOLS

Safety Symbols alerting you to potential personal safety hazards. Obey all safety

messages following these symbols.

 WARNING  CAUTION

avoid possible avoid possible

injury or death injury and/or property damage

FOR YOUR SAFETY READ ALL INSTRUCTIONS

BEFORE INSTALLATION AND OPERATION

Installer: Provide these instructions to the consumer.

Consumer: Keep documents for future reference.

Atwood Levelegs™ Levelers are intended for use on recreation vehicle

motorhomes and trailers.

 WARNING

VEHICLE CAN MOVE OR COLLAPSE

• Never exceed the rated capacity of the leveler as stated on its label.

• Levelers are not designed to be used as jacks. Do not use levelers to

lift the vehicle during tire changes, axle work or other servicing. The

tires must stay on the ground.

INSTALLATION

LEVELER LEG

1. Prior to installation, retract the levelers so the foot pads are within

1/2˝ to 1˝ from the end of the outer housing (FIG 1-A).

2. Remove Round Tube Leveleg.

3. Attach new Frame Bracket (

FIG 2-A) to existing location on frame

(FIG 2-B), using hardware kit provided. Depending on the model use

four (4) to six (6) each 1/2 - 13 Grade 5 bolts and nuts and 12 of the

1/2˝ Type A washer.

4. Position leveler vertically against frame so base of foot has 8-9˝

minimum ground clearance when vehicle is loaded to its maximum

GVWR (

FIG 1-B).

5. Fit the Leveleg bracket (FIG 2-C) around the Leveleg, (FIG 2-D)

engaging one tab in the slot of the bracket (

FIG 2) and the other tab

(FIG 2-E & F) below the bracket (FIG 2). Bracket may be rotated 180˚ for

more/less ground clearance and either set of mounting holes may be

used. Attach the Leveleg bracket to the frame bracket with 1/2˝ - 13

grade 5 bolts and 1/2˝ flat washers on the Leveleg bracket and a 1/2˝

flat washer, 1/2˝ locking washer and 1/2˝ - 13 grade 5 nut. To install

on 5th wheel trailers, refer to MPD 71125.

Lubricate the bolts and torque to 65 ft-lbs. Insure the top two and

bottom two holes in leveler brackets have bolts in them.

ELECTRICAL CONNECTIONS

1. Check the existing old round tube leveler.

ONE (1) PLUG ON WIRES COMING FROM THE MOTOR - Wiring Harness supplied

in this kit is not

required.

TWO

(2) PLUGS ON WIRES COMING FROM THE MOTOR - Find the wires from the

motorhome signal wire harness that were attached to the round

tube leveler. Connect those two wires to the two plugs from the

‘Y’ wire harness (FIG 3-A).

Figure 1

Figure 2

Figure 3

 WARNING  CAUTION 1
 WARNING 1

Indice de contenidos

Pagina 1 -  WARNING

9LITERATURE NUMBERMPD 61050LEVELEGS™ SYSTEMADAPTER KITENGLISH, FRANÇAIS (et Canada) Effective 12/12/0724 HOUR TROUBLESHOOTING HELP CALL - 800-884-7012

Comentarios a estos manuales

Sin comentarios

Atwood Levelegs System Adapter Kit Manual de usuario

Busca en linea o descarga Manual de usuario para Para El Coche Atwood Levelegs System Adapter Kit. atwood Levelegs System Adapter Kit User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Para El Coche Atwood Levelegs System Adapter Kit