Atwood Levelegs System Manual de usuario descargar pdf

SAFETY ALERT SYMBOLS

Safety Symbols alerting you to potential personal safety hazards. Obey all safety

messages following these symbols.

 WARNING  CAUTION

avoid possible avoid possible

injury or death injury and/or property damage

FOR YOUR SAFETY READ ALL INSTRUCTIONS

BEFORE INSTALLATION AND OPERATION

Installer: Provide these instructions to the consumer.

Consumer: Keep documents for future reference.

Atwood Levelegs™ Levelers are intended for use on recreation vehicle

motorhomes and trailers, any other use is strictly prohibited.

 WARNING

VEHICLE CAN MOVE OR COLLAPSE

• Never exceed the rated capacity of the leveler as stated on its label.

• Levelers are not designed to be used as jacks. Do not use levelers to

lift the vehicle during tire changes, axle work or other servicing. The

tires must stay on the ground.

INSTALLATION

LEVELER LEG

1. Prior to installation, retract the levelers so the foot pads are within

1/2˝ to 1˝ from the end of the outer housing (FIG 1-A).

2. Position leveler vertically against frame so base of foot has 8-9˝

minimum ground clearance when vehicle is loaded to its maximum

GVWR (FIG 1-B).

3. A. For 7.5K Square Tube Levelegs™, attach the frame bracket (

FIG 12-C)

to frame (FIG 12-D) using 4 sets of 1/2˝ - 13 grade 5 nuts and bolts

and 1/2˝ flat and locking washers. Fit the Leveleg bracket (FIG 12-E)

around the Leveleg, (

FIG 12-F) engaging one tab in the slot of the

bracket (FIG 12-G) and the other tab below the bracket (FIG 12-H).

Attach the Leveleg bracket to the frame bracket with a 1/2˝ - 13

grade 5 bolt and 1/2˝ flat washer on the Leveleg bracket and a 1/2˝

flat washer, 1/2˝ locking washer and 1/2˝ - 13 grade 5 nut. To install

on 5th wheel trailers, refer to MPD 71125.

B. For 10K Square Tube Levelegs™, attach the leveler bracket (

FIG 13-J)

to the frame bracket (FIG 13-C) using four (4) each 1/2˝-13 grade 8

bolts and 1/2˝ flat hardened washers.

C. For 15K Square Tube Levelegs™, attach the leveler bracket (

FIG 14) to

the frame bracket (FIG 14-C) using six (6) each 1/2˝-13 grade 8

bolts and 1/2˝ flat hardened washers.

Lubricate the bolts and torque to 65 ft-lbs.

CONTROLS

FOR 5TH WHEEL CONTROLS REFER TO MPD 87920 AND 71125.

Relay Pack Controller

 WARNING

EXPLOSION

• Controller is not ignition protected. DO NOT install in areas that

require ignition protected devices (such as battery or propane tank

storage compartments).

1. Install Relay Pack Controller in a clean, dry interior area protected

from moisture. Use corner holes of unit to fasten base horizontally

to mounting surface, using appropriate hardware for surface.

2. Install the AUTO POSITION Relay Pack Controller so the forward

arrow points toward the front of the motorhome. The Relay Pack

must be right side up and within 10º of horizontal level (

FIG 3).

Auto Position Control Pads

1. Locate the controller midway between front and rear wheels of the

vehicle. Provide a 4-15/16˝ (

FIG 2A) x 3-3/16˝ (FIG 2B) cutout with a

1/4˝ angled edge (

FIG 2C) at 45˚ (FIG 2D) for the control pad at

desired location. Note: Reference control pad when making cutout;

there is tight clearance.

2. Use corner holes (

FIG 2E) of unit to fasten control pad to mounting

surface using appropriate hardware for surface.

Note: Fastener must pierce mylar surface of control pad.

3. Connect control pad wire harness (FIG 3H) to control pad.

4. Route the control pad wire harness to controller and connect the

two (

FIG 3-J).

5. Control pad wire harness is configured as follows (FIG 4).

Required Parts

ITEM DESCRIPTION QTY

A+B 43025-0400 Molex

Micro-fit 3.4 circuit receptacle 2

C 43030-0007 Molex

Micro-fit 3.0 female terminal 8

D Unshielded 22 AWG multiconductor cable 1

Pin Requirements

CONNECTOR PIN COLOR CONNECTOR PIN COLOR

A1 White B1 White

A2 Green B2 Green

A3 Red B3 Red

A4 Black B4 Black

6. Crimp the contacts with approved Molex

die.

7. Crimped contact must be able to withstand a minimum of nine

(9) pound pull force.

8. Terminate sleeve of multiconduit cable to within 1˝ of connector

(

FIG 4-E)

9. Adjust the length of harness as required to easily connect control

pad to controller (

FIG 4-F).

LITERATURE NUMBER

MPD 66166

LEVELEGS

™

SYSTEM

ENGLISH,

FRANÇAIS (et Canada) Effective 11.21.07

24 HOUR TROUBLESHOOTING HELP CALL - 800-884-7012

Provided by Coach Net

, the largest RV owner support company in North America.

Not affiliated with/supported by/or warranted by Atwood Mobile Products

•Installation •Operation •Maintenance

1 2 3 4 5 6 7

Indice de contenidos

Pagina 1 -  WARNING

1SAFETY ALERT SYMBOLSSafety Symbols alerting you to potential personal safety hazards. Obey all safetymessages following these symbols. WARNING  CAU

Pagina 2 -  CAUTION

2MOTOR HOME SIGNAL WIRE HARNESS1. Connect the motor home signal wire harness (FIG 3-I) to the con-troller (FIG 3-K).2. Motor home signal wire harness

Pagina 3

3CONTROL PAD LED INDICATORSThe control pad LED’s indicate the following when illuminated (FIG 9):DESCRIPTION COLOR ITEMVehicle Engine running (ignitio

Pagina 4

4 CAUTIONPERSONAL INJURY/PRODUCT DAMAGE• Battery operated drills, 9.6V to 18V, are powerful. Hold drill with bothhands to protect your wrist. Keep lo

Pagina 5

5Guides are only intended for use on Atwood®products by service tech-nicians who have successfully completed Atwood®training. This guideshould be used

Pagina 6 - R2 C E FS

6FFigure 4 — Control Pad Wire HarnessFigure 5 — Battery ConnectionFigure 6 — Delphi ConnectorFigure 7 — Controller Molex ConnectorAE ECAEDCBBFDA1

Pagina 7 - Figure 3

7Figure 3ABFigure 1 — Leveleg InstallationFigure 2 — Control Pad TemplateCDIDS Inc. P/NSIGNAL WIREHARNESSICONTROLPADHFGFMLGMLMLLMDUMPATWOODRELAY PA