EXTENDED
RETRACTED
D
A
C
B
A
E
B
C
EXTENDED RETRACTED
90 Outward
60 Inward
Camper Corner
(Long Angle)
Corner
Brackets
Jack Attachment
(Short Angle)
Jack Attachment
(Short Angle)
Camper Corner
(Long Angle)
PASSENGER SIDEDRIVERS SIDE
FORWARD
CAMPER
A
B
ENGLISH •Installation •Operation •Maintenance
Effective 12/04/07
LITERATURE NUMBER MPD 87904
SWING OUT BRACKET
9
Use with Atwood Acme and Ball Screw Truck Camper Jacks when additional
width between the two front jacks is required to clear the fenders on dual
wheel trucks. Due to the variety of camper sizes and truck trims, please
verify that these swingout brackets provide enough clearance for driver
comfort during loading and unloading.
For complete Acme and Ball Screw truck camper installation, operation instructions
consult MPD 87903.
MPD 85428 - New White
MPD 85473 - Pure White
Swing Out Bracket Kit contains -
1 Driver Side brkt. Note the single grooved bushings (
FIG 1-A).
1 Passenger Side brkt. Note the double grooved bushings (FIG 1-B).
6 Nuts and bolts
12 Washers
INSTALLATION
1. The end with the 1/4˝ thru-bolt must be at the top of the bracket
during installation (FIG 2-A).
2. The angle bracket welded to the bushing with the thru-bolt attaches
to the bracket already on the camper corner (
FIG 1-C / 2-B).
3. Use three-3/8˝ x 1-1/2˝ long Grade 5 bolts and washers to attach
each bracket. Torque bolts to between 15-20 ft. lbs (FIG 1-D).
4. Attach jack to other angle bracket with three 3/8˝ x 1-1/2˝ long Grade
5 bolts and washers. Torque bolts to between 15-20 ft. lbs (
FIG 1-D).
NOTE: For Acme and Manual Ball Screw Jacks switch the front jacks
from driver side to passenger side and vice versa to allow the
crank handle to operate.
WARNING
PERSONAL INJURY & PRODUCT DAMAGE
• Do not operate jack set if camper exceeds gross vehicle weight rating.
• Maintain proper load distribution and safe distance when raising or
lowering camper.
• Never walk under the camper when it is extended on the jacks.
• Only operate jacks when camper is unoccupied and contents are
secured and properly distributed.
• Position swing out brackets properly. In the Extended Position - 90°
outward to the side of camper (
FIG 3-A) and in the Retracted
Position - 60° inward to the side of camper (FIG 3-B).
• Jack bracket must be in retracted position when traveling on roadway
(FIG 3-B).
OPERATION
Extended Position -
Lift jack and swing outward from camper body to
clear truck’s dual wheel fenders. When jack is in the extended position,
be sure the bracket attached to the jack (FIG 2-D) rides up into the notch
in the camper corner angle bracket attached to the camper (FIG 2-D).
This must be done visually prior to loading jack.
Retracted Position - After the jack is retracted, lift the jack and rotate it
forward (inward) so when released, the bracket attached to the jack rides
down into the notch in the camper corner angle (FIG 2-E).
MAINTENANCE
1. Spray entire bracket with silicon spray lubricant at least once each
camping season. Wipe off excess.
2. Regularly observe swingout brackets for unusual wear, weld
imperfections or cracks, or any condition that compromises
performance.
3. Should problems, concerns or questions arise contact your Dealer,
Camper Manufacturer or the Atwood Service Department at
574-262-26555.
A - Driver Side
B - Passenger Side
C
D
D
D
FIG 1
FIG 2 FIG 3
(4 paginas)
(2 paginas)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales