Atwood Gooseneck Couplers Manual de usuario Pagina 2

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 3
  • Tabla de contenidos
  • MARCADORES
  • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 1
2
COUPLING PROCEDURE MPD 75401 & 75004
1. On level ground place wheel chocks in front and behind wheels,
both sides of the trailer (4 chocks).
2.
FIG 1 shows coupler handle in a latched position. To open, rotate
handle
FIG 2-D counterclockwise a sufficient amount to allow handle
tab FIG 1-E to clear rivet tab FIG 1-F, then pull handle away from cou-
pler and position handle tab under rivet on outside of rivet tab as in
FIG 2.
3. Adjust trailer jacks until coupler is at level height or slightly lower
(by 1˝) than top of hitch ball.
4. Lower tailgate of truck.
5. Back truck slowly toward trailer until coupler drops into place over
the ball. Check to see that the ball has entered the ball cup of the
gooseneck coupler.
6. Coupler will not completely lock into place until trailer jacks are retracted.
7. Connect power line, breakaway switch line and safety chains
between truck and trailer (see trailer manufacturer’s instructions).
8. Retract trailer jacks.
9. Check to make sure that the handle is in latched position. Place
lock pin
FIG 2-G in holes of tabs FIG 2-H, pinning the handle in
place.
10. Close and latch tailgate. Check all lights - stop, turn, tail, and
brake lights for proper operation.
11. As an additional check before towing, extend jacks until truck is
raised 3 to 4˝ to verify that coupler is securely attached to ball.
12. Completely retract trailer jacks.
13. Pick up and store wheel chocks.
UNCOUPLING PROCEDURE MPD 75401 & 75004
1. On level ground place wheel chocks in front and behind wheels,
both sides of the trailer (4 chocks).
2. Lower trailer jacks. If on soft ground, place a support under the jack
feet to prevent trailer from settling.
3. Lower tailgate on truck.
4. Remove the lock pin
FIG 2-G and rotate handle counterclockwise.
Pull handle
FIG 2-D away from coupler and position the handle tab
FIG 2-E under rivet on rivet tabs FIG 2-I.
5. Raise trailer until jacks lift coupler completely above the top of ball.
6. Disconnect power line, breakaway switch line and safety chains
between truck and trailer.
7. Drive truck slowly away from under trailer.
MAINTENANCE
WARNING
PERSONAL INJURY / PROPERTY DAMAGE
Replace worn or damaged parts.
Do not tow trailer with worn or damaged parts.
GOOSENECK COUPLER MPD 75025
1. Monthly, clean ball cup and clamp, lubricate with wheel bearing grease.
2. Monthly, apply SAE 30 oil at points where the handle rotates at
sides of coupler.
3. Check ball and coupler before each trip for wear.
DROP-TUBE STEM & COUPLER MPD 75401
1. Before each use check torque on the 1˝ diameter bolt 4-E, it should
be 100 ft/lbs.
SCREW ADJUSTABLE STEM & COUPLER MPD 75004
1. On level ground place wheel chocks in front and behind wheels,
both sides of the trailer (4 chocks). Disconnect the coupler from the
hitch ball.
2. To lubricate the adjustable stem, extend the coupler as far as possi-
ble, and squirt SAE 30 oil into the top of the stem where the screw
extends out of the top.
3. After oiling, completely retract the stem, and reposition it as
described in Operation Instructions.
For problems or questions, contact your dealer, the trailer mfg., or
Atwood’s Consumer Service Department 574-264-2131.
Atwood Hardware Systems & Components Limited Warranty
For warranty information contact Atwood (574-264-2131) before having any work
done. Atwood Mobile Products warrants to the original purchaser that this product will
be free of defects in material and workmanship for a period of 2 years from the date of
purchase. Atwood’s liability hereunder is limited to the replacement of the product,
repair of the product, or replacement of the product with a reconditioned product at the
discretion of the manufacturer. The warranty is void if the product has been damaged
by accident, unreasonable use, neglect, tampering or other causes not arising from
defects in material workmanship. The warranty extends to the original consumer pur-
chaser of the product only, and is subject to the following conditions:
1. For two (2) years from the original date of purchase, Atwood will replace or repair or
replace with conditioned product, at Atwood’s discretion, product found to be defec-
tive in material or workmanship. Weights on each individual leg are required to
process the warranty request.
2. In the event of a warranty claim, the Original Owner must contact the
Atwood Consumer Service Department, 1120 North Main St., Elkhart, IN
46514, Telephone: 574-264-2131 Fax: 574-206-9713. Warranty claim
service must be performed as approved by the Atwood Consumer
Service Department. Warranty replacement hardware systems and com-
ponents or parts will be furnished freight prepaid. Labor cost to repair or
replace will be limited to the amount of the original purchase price of the
systems and components. The replaced warranty products or parts
become the property of Atwood Mobile Products and must be returned to
the Atwood Consumer Service Department freight prepaid, unless prior
arrangements have been agreed to.
3. This limited warranty is valid only when the product is applied, installed,
maintained and operated in accordance with this Atwood Installation,
Maintenance and Operating Manual. Any deviation from these recom-
mended specifications must be approved in writing by Atwood.
4. Any implied warranties are limited to the duration of this limited warranty
as stated above. Atwood does not assume responsibility for consequen-
tial damage or loss, including loss of use of vehicle, loss of time, incon-
venience, expense for gasoline, telephone, travel, lodging, loss or damage
to personal properties, or loss of revenues. Some states do not allow limi-
tations on how long an implied warranty lasts or limitations on conse-
quential damages, so the above limitations may not apply to you. This
limited warranty gives you specific legal rights which may vary from state
to state.
Vista de pagina 1
1 2 3

Comentarios a estos manuales

Sin comentarios